How To Repair American Standard Kitchen Faucet Single Handle
Once once more, the faucet O-ring seals are leaking. This happens most every 2 years, perhaps due to mineral buildup in the spout trunk despite the water softener. Fortunately, it's a dribble rather than a spurt, and then it's non an emergency.
This is a Abode Depot (or was it Lowe'due south?) faucet, but they exercise not stock repair parts. Go to FaucetDirect.com, order these parts:
- 060366-0070A SPOUT SEAL KIT (on the main column)
- 060343-0070A SPACER WITH O-RINGS (below the valve cartridge)
- 030126-0070A BUTTON AND SCREW KIT (if yous booger the push button)
Of course, order two or three of each, considering FD has castigating aircraft rates. 10 bucks for a few envelopes of O-rings? Sheesh… simply the last fourth dimension I tried to become 'em locally, they were No Stock. If I've got to expect around, I'll have 'em delivered to my door.
[Update: that comment suggests you can at present get 'em from Amazon.com]
The first puzzle is how to go the faucet apart. Later on making a mess of it the first time, it turns out you poke a small flat screwdriver inside the handle and pop the reddish-blueish push button out. It'southward held on by ii small-scale tabs, one on each side, and if y'all tin simply push one then information technology'll ease right out. It is non a spiral head, despite the recessed slot down the middle.
Poke a 3/32″ hex key in the hole, back out the setscrew a few more than turns than yous think information technology takes, pull the handle off.
The plastic cap retainer has two arms holding the escutcheon ring in identify. Push inward, remove the escutcheon. The servant is probably hopelessly jammed into the peak of the faucet spout, so if it doesn't come out, that's OK.
Loosen the three screws belongings down the valve cartridge, pull it straight up and out. You lot did plough the water off get-go, right? Remove the plastic spacer plate and 3 O-rings below information technology if yous can; the plate may not fit through the retainer.
Now, get comfortable on the sink. Pull-and-twist the spout straight upwardly with far more than force than you think necessary. It volition suddenly wing off and bloosh the water that's been standing in the faucet column all over the place.
You lot're left with a rather grody column and the 2 offending O-rings. Note the orientation of the argent flange ring at the bottom and the lower white plastic bearing ring. At that place may be three O-rings stuck to the superlative surface; they belong inside the spacer plate.
Remove all that hardware and scrub the grodosity off the column.
Hint: if you're weak of stomach, never look inside your drinking water fixtures, because y'all'll never drinkable tap water again.
I by and large soak the spout in vinegar for a bit, scrub it out with a toothbrush, ease the remaining deposits off with a pocket-sized screwdriver, then scrub the whole thing down with a ScotchBrite pad.
I apply a very very very thin layer of silicone lubricant to the bearing surfaces inside the column, which makes the next step possible.
Put the flange ring, the new O-rings, and plastic bearing rings in place, and then slide the spout assembly direct down over the column until it bottoms out with a thump.
Install the new spacer plate & its O-rings, and so reassemble all the other doodads in reverse gild, plow on the h2o, and you're done.
Then forget all the grime you saw in in that location that yous couldn't clean out.
Source: https://softsolder.com/2009/11/02/american-standard-elite-kitchen-faucet-disassembly/
0 Response to "How To Repair American Standard Kitchen Faucet Single Handle"
Post a Comment